KARE+

The detector emits a beep

If the sensor beeps every minute, this indicates a low or discharged battery.
There are several reasons for battery discharge:

• Failure to maintain the detector (dust at least once a year)
• Repeated false alarms or sub-optimal operating conditions

The detector emits three beeps

Three repetitive beeps every minute or so indicate that the sensor has detected a fault in its smoke sensor. Follow the test procedure below to clean and test the detector:

• Remove the detector from its base (1/4 turn to the left).
• Clean the detector using the brush attachment of a vacuum cleaner to remove any dust that may have accumulated and interfered with the product’s operation.

• Check sensor operation. Press the central button for at least 3 seconds:

• • Case 1: If the sensor emits a loud beep and the Red LED flashes, the sensor is functional and should be reinstalled on its mounting base.
  • Case n°2: If the sensor does not sound and the Red LED flashes dimly, the battery is low and the detector must be replaced.
  • Case 3: If the sensor does not sound and the Red LED does not flash: wait 2 minutes.
    If the sensor emits 3 consecutive beeps every minute, the sensor is faulty and the product must be replaced. If the sensor does not beep, the battery is empty. The sensor is no longer operational and must be replaced.

Check beforehand the precautions and limits of use of the detector, as well as the maintenance recommendations given in the user manual.

The presence of dust, the immediate proximity of an artificial light source, or nearby air movement caused by a convector, air-conditioning or ventilation unit, can cause the detector to go off for no apparent reason.
To maintain it, simply clean your detector (at least once a year) using the brush attachment of a vacuum cleaner and, if necessary, change its location.

Do not install the smoke detector in :

• Less than 1.5 m from lighting fixtures: ceiling lights, incandescent, halogen or fluorescent lamps, etc.
• A place where the detector is exposed to direct sunlight
• Close to or above heaters, windows or other equipment that can generate air flows
• Proximity to stray fumes: chimneys, furnaces, boilers, combustion radiators, etc.
• A place where the temperature is below 4°C or above 45°C. A place where humidity is below 10% or above 95%: bathroom, laundry room, etc.
• A dusty or dirty area: garage, workshop, etc.
• An insect-infested or outdoor location

WARNING: for your own safety, do not disable your sensor if it is operating correctly!

To switch off a sealed-battery sensor, simply take a paper clip, insert it into the square hole at the back of the product, and pull slightly to raise the switch. If the sensor has a changeable battery, simply remove the battery to switch the product off.

Please wait at least 20 seconds before switching the detector back on.

At the end of its service life, the connected smoke sensor reacts as follows:

• Audible alert beeps 3 times every 45 seconds

The detector is not operational. The detector has been active for more than 10 years, and needs to be replaced.

For all new products purchased, the company offers a commercial warranty on the durability of “Autonomous Warning Detectors”, covering product defects with regard to the functions for which the sensor was designed, in compliance with applicable standards, for a period of 5 years from the date of purchase. This longer-term guarantee
is free of charge. It does not constitute insurance. It is in addition to your legal warranties of conformity and hidden defects.
This warranty applies subject to compliance with installation, assembly and maintenance instructions, as well as precautions and limitations of use.
of the product.

It does not apply if the product has been modified/adapted, disassembled, if the serial number is illegible, in the event of damage to the sensor caused by improper storage conditions, failure to observe mounting and maintenance instructions and/or precautions and limits of use.

Any malfunction or non-operation of the sensor due to dust and/or insect infestation, despite maintenance in accordance with these instructions, is considered to be normal wear and tear and is not covered by the warranty. For details of how to make use of the warranty, please refer to the Service section of the User Manual and follow the instructions.
In the event of a product defect detected by the after-sales service and if the conditions for implementing the commercial warranty defined above and those set out in the § After-sales service are met, NEXELEC undertakes to repair free of charge the product returned by you at your expense or to replace it with an identical product.

SERVICE

Before you can apply for the contractual warranty, you must consult the information available on the www.nexelec.us website and obtain a return number. No warranty claims will be accepted without a warranty number.
back.

If a defect is detected during the warranty period, the purchaser must send the sensor to NEXELEC’s after-sales service department at his own expense.
The sensor must be accompanied by a dated proof of purchase and a warranty claim form describing the defect.